McKay Church Goods- Church Supplies
McKay Church Goods- 1-800-749-2340

BANNER STANDS

Banner Stand
Sleekly styled, this approx. 100" tall stand
displays banners up to 36" wide. Bar is 38" long.
Made of brasstone finish that will never tarnish.
12-3/4" weighted brasstone round base or 10-5/8" x 9"
three-step solid brass rectangular base to match
other church appointments.
Can be carried in a processional.
 Item # Description Price Qty
 WR1026     Banner Stand will display banners up to 36" wide. Bar is 38" long. Made of Brasstone finish that will not tarnish. Shown with an 11-7/8" square 3-step Walnut Wood Base. Can be carried in a processional - pole breaks about 10" from the bottom of the base. Banner attaches to top by 2 "S-hooks" which are included. Banner stand is 100"H, 21 lbs.   $669.00  
 WR1026K     Same as above but has 3-Step Oak Base   $669.00  


Solid Brass Banner Stand
Processional, furnished with removable
telescoping shaft or rigid shaft.
Base 10-1/2", cross arm 36", brass satin finish.
Banner needs a rod pocket and slit in the middle of the back of the banner.
Screw in center of horizontal top loosens to allow you to slide one end of the pole through the middle slit
of the banner and then slide the other end of the pole through the other side of slit of the banner.
Horizontal bar cannot be pulled out completely - have to use the technique as described.
 Item # Description Price Qty
 K173-B    Processional Banner Stand
Telescoping shaft extends 51" to 90", solid brass, base 10-1/2".		 $645.00  
 K173-C    Processional Banner Stand
60" Rigid Shaft, solid brass, base 10-1/2".		 $575.00  
 K173FB    Extra - Add 12" Weighted Solid Brass Base as on Style #K174 banner stand below $95.00  
 K173T    Extra - Furnish with telescoping cross arm, extends 24" to 45" $110.00  
 HSPEC    Add To The Height of Banner Stand By The Inch, $4.00 per inch $4.00  
 WSPEC    Add To The Width of Banner Bar By The Inch, $4.00 per inch $4.00  
 K174DB    Add A Double Bar - Increases By The Inch, $5.00 per inch $5.00  



K-172: Solid Brass Banner Stand
Non-processional with telescoping shaft.
Shaft extends 51" to 90".
Base 9", cross arm 30". Brass satin finish.
K-175: Solid Brass Banner Stand
Processional & telescoping, extends 51" to 90".
32" double cross arm. Any type banner attached by
removing one screw, and sliding on banner.
 K172                                                K175
 Item # Description-SHOWN LEFT TO RIGHT Price Qty
 K172    Solid Brass Non-Processional Banner Stand
Has telescoping shaft, extends 51" to 90".
Base 9", cross arm 30". Brass satin finish. Base approx. 12-15 lbs.		 $560.00  
 K172A    Upgrade base for K172 banner stand to 10-1/2" base for heavier banners.
Base approx. 18 lbs.		 $75.00  
 K175    Solid Brass Processional and Telescoping Banner Stand
Extends 51" to 90". Double cross arm is 32".
Any type banner attached by removing one screw, and sliding on banner.
10-1/2" base. Brass satin finish. Base approx. 18 lbs.		 $670.00  
 K175-B    Upgrade base for K175 banner stand to 12" base for heavier banners
Base heavier than 18 lbs.		 $765.00  
 HSPEC    Add To The Height of Banner Stand By The Inch, $4.00 per inch $4.00  
 WSPEC    Add To The Width of Banner Bar #K172 By The Inch, $4.00 per inch $4.00  
 DSPEC    Add To The Width of Double Bar #K175 By The Inch, $5.00 per inch $5.00  



Solid Brass Banner Stand
Processional, furnished with removable
telescoping shaft or rigid shaft.
Base 10-1/2", cross arm 36", brass satin finish.
Banner needs a rod pocket and slit in the middle of the back of the banner.
Screw in center of horizontal top loosens to allow you to slide one end of the pole through the middle slit
of the banner and then slide the other end of the pole through the other side of slit of the banner.
Horizontal bar cannot be pulled out completely - have to use the technique as described.
 Item # Description-SHOWN LEFT TO RIGHT Price Qty
 K174     Highly Polished Brass Processional Banner Stand
Has telescoping shaft, extends 51" to 90".
12" Weighted Base, cross arm fixed at 36".		  $710.00  
 K174-DB     Same as above but with 36" fixed double bar.  $825.00  
 K174-U     Add larger 12" base to either K174 or K174-DB Banner Stand  $95.00  
 K174T     Processional Banner Stand with telescoping cross arm, extends 24" to 45"  $820.00  
 HSPEC     Add To The Height of Banner Stand By The Inch, $4.00 per inch  $4.00  
 WSPEC     Add To The Width of Banner Bar By The Inch, $4.00 per inch  $4.00  
 DSPEC     Add To The Width of Double Bar By The Inch, $5.00 per inch  $5.00  
 ENG     Engrave the Base of K174 Banner Stand, $1.00 per character will be added to your total  $1.10  



  
 Item # Description-SHOWN LEFT TO RIGHT Price Qty
 2424      Processional Banner Stand, 12-foot Height, 14" square steel base.
1-3/8" wooden pole diameter, assembles at midpoint, slot in top for banner cord. Price includes crossbar. Ideal for 9-1/2-foot by 3-foot Slabbinck Indoor Banners Sold Separately on our Website Under Church Banners PLEASE NOTE: LAST PICTURE TO RIGHT SHOWS THIS BANNER STAND ASSEMBLED******		    $380.00  
 2493      Banner Stand, 8-foot Height, 12" base.
33" cross bar with removable ends. Made of brass tubing with a steel weight in the base. Removable shaft at midpoint (shown where arrow is pointing), has a washer at the center of the banner top that the cross screws into.
Designed to hold a banner that weighs under 15 lbs.		    $715.00  
 2477      Banner Stand, 8-foot Height, 12" steel base.
33" wide cross bar with removable ends, black aluminum shaft.
Above Green Banner-wth approx. 2" rod pocket (sold separately under church banners on our website) slides on to crossbar.		    $405.00  



Banner Stand from Slabbinck
Easily displays banners or tapestries,
either in the sanctuary or church.
 Item # Description Price Qty
 5036  Banner Stand, solid, telescopic, chrome plated metal.
Height adjusts from 70" to 177", width adjusts from 28" to 54".
Two sets of hooks (front and back) so two banners can be hung at the same time.		 $445.00  




 Item # Description Price Qty
 TT1214     Banner Stand, 106" Overall Height Includes Base and Cross
Banner pole is 96" and separates at mid-point for processional use. Can also remove pole from base and process with entire pole. Base is hollow with a plug - fill base with sand to make the banner stand sturdy. Comes with loop of fabric to stabilize. Banner not included.		   $495.00    
 TT1214     Extra Base For Banner Stand   $70.00    



Always remember to inquire if you have a special request!

For more information
please contact us: Toll Free: 1-800-749-2340
In Cleveland: (330) 487-1134
FAX: (330) 487-5158
e-mail: info@mckaychurchgoods.com

Home | Monthly Specials | PRODUCTS | Custom Items
About Us | Sales Polices | Catalog Order Form | E-Mail McKay

©2002-2018 McKay Church Goods Banner Stands